Compressive Strength of Cement: Mortar Cube Test, IS 4031 Part 6

compressive strength of cement

The compressive strength of cement is the load a 1:3 cement-sand mortar cube carries before it crushes. Labs report it in N/mm² at 3, 7 and 28 days. Because this number sets every cement grade, it shows whether a bag sold as OPC 53 really is OPC 53. This guide covers the IS 4031 Part 6 test, its apparatus, the calculation and the grade limits.

Key takeaways

  • IS 4031 (Part 6):1988 tests cement on 70.6 mm cubes of 1 part cement to 3 parts standard sand.
  • The OPC grade number is its minimum 28-day strength in N/mm².
  • Cubes are crushed at 3, 7 and 28 days, with three cubes at each age.
  • The load rate is 35 N/mm² per minute, and results round to the nearest 0.5 N/mm².
  • A cement cube result is not a concrete strength.

What is the compressive strength of cement?

The compressive strength of cement is the crushing strength of a standard mortar made from that cement. The lab fixes the sand, water, curing and load rate. As a result, the cement is the only variable.

IS 4031 (Part 6):1988 covers the compressive strength of hydraulic cement other than masonry cement, such as OPC and PPC. The Bureau of Indian Standards has reaffirmed Part 6 rather than replaced it, so the 1988 text with its amendments is still current.

Apparatus for the compressive strength of cement test

The test needs six items. Each one is specified, so results match from lab to lab.

  • 6 mm cube moulds, with a face area of about 50 cm²
  • A vibration machine at 12,000 ± 400 vibrations per minute
  • IS 650 standard sand
  • A Vicat apparatus, to find the standard consistency (P)
  • A moist closet at 27 ± 2 °C and at least 90% humidity
  • A compression testing machine

IS 650 sources the standard sand from Ennore, near Chennai. So labs across India cast their cubes with the same sand.

How to do the cement compressive strength test

The test mixes, casts, cures and then crushes three cubes for each age. Here is the IS 4031 Part 6 sequence:

  1. Weigh: Weigh 200 g of cement and 600 g of standard sand per cube.
  2. Add water: Add (P/4 + 3.0)% water by combined mass, where P is the standard consistency.
  3. Mix: Mix for at least 3 minutes. If even colour takes over 4 minutes, start again.
  4. Cast: Fill the mould, rod the first layer 20 times, then vibrate for 2 minutes.
  5. Moist cure: Keep the moulds in the moist closet for 24 ± 1 hours.
  6. Water cure: Then cure the cubes in clean water at 27 ± 2 °C, renewed every 7 days.
  7. Crush: Load three cubes per age on their sides at 35 N/mm² per minute.

Test ages count from the end of vibration. For example, a cement with P = 30% needs 10.5% of 800 g, which is 84 g of water.

How to calculate the compressive strength of cement

Divide the failure load by the loaded area of the cube. Then round the result to the nearest 0.5 N/mm².

Compressive strength (N/mm²) = Maximum load (N) ÷ Area (mm²)

For example, a cube fails at 250 kN. Its area is 70.6 × 70.6 = 4,984 mm². So the strength is 250,000 ÷ 4,984 = 50.2 N/mm², reported as 50.0 N/mm².

The report gives the average of three cubes. However, the lab sets aside any faulty cube, or one more than 10% off the average. If fewer than two results remain, that age is tested again.

Compressive strength of cement by grade

Each cement standard sets a minimum strength at each age. OPC 33 and OPC 43 also have a 28-day maximum, so a cement can fail for being too strong.

Cement type

Standard

3 days (min)

7 days (min)

28 days (min)

28 days (max)

OPC 33

IS 269

16

22

33

48

OPC 43

IS 269

23

33

43

58

OPC 53

IS 269

27

37

53

—

PPC (fly ash)

IS 1489 (Part 1)

16

22

33

—

All values are in N/mm². PPC gains strength more slowly in the first week. Therefore, judge PPC against its own limits, not against OPC 43.

Cement cube vs concrete cube

A cement cube tests the cement, while a concrete cube tests the mix. Concrete cubes use the real site mix and follow IS 516. So OPC 53 cement does not make M53 concrete.

For site concrete, see our concrete testing lab. To set mix proportions, see design mix testing.

Why does a cement sample fail?

A low compressive strength of cement result usually points to storage, or to a slip in the test.

  • Old or damp cement: cement loses strength as it picks up moisture, so check the date on the bag.
  • Wrong water: guessing instead of testing consistency shifts the result.
  • Temperature drift: curing outside 27 ± 2 °C changes the rate of strength gain.
  • Faulty cubes: poorly vibrated cubes crush early.

Next, retest a sealed bag from the same batch and ask the supplier for the test certificate. Under the Cement (Quality Control) Order, 2003, cement sold in India must carry the BIS Standard Mark.

For a result that will settle a dispute, use a lab accredited by NABL. Our cement testing lab runs this test under our NABL accreditation.

Get Your Cement Tested at Jancy Labs

Jancy Labs Private Limited is an accredited civil material testing laboratory (ISO/IEC 17025:2017, Certificate No. TC-12176) in Madurai, Tamil Nadu. We collect samples across Tamil Nadu and accept courier samples from anywhere in India.

Or call +91 86800 49004 · jancylabsmdu@gmail.com · Request a quote

4.8★ · 100+ Google reviews · Mon–Sat, 10:00–18:00

Frequently Asked Questions

What is the compressive strength of cement at 28 days?

It depends on the grade. Under IS 269, OPC 33, 43 and 53 must reach at least 33, 43 and 53 N/mm². Fly ash PPC must reach at least 33 N/mm².

How long does the cement compressive strength test take?

The full test takes 28 days. However, results arrive in stages at 3, 7 and 28 days, so a weak cement shows up early.

Can site sand be used instead of standard sand?

No. IS 4031 Part 6 calls for IS 650 standard sand. Site sand changes the result, so the test would no longer measure the cement alone.

How many cubes does the test need?

Three cubes per age. So a full 3, 7 and 28-day test needs nine cubes from the same sample.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top